well you could try a thumb print, however, it'll be the ride of your life. =P
I suggest following JOR instructions.
Laying LSD crystal to blotter accurately
Let us assume you can obtain the following.
A page of 900 hits of standard commercially available blotter paper (this works for anything comparable to Key-Z and Shakedown, must be modified for other types of paper based on their absorbancy, KNOW YOUR PAPER) 90-100mg of xtal (to account for any crystal impurities, let us assume you use 100, this lays roughly 110 mics per hit of crystal which you then have to multiply by your purity, assuming a 95% crystal that is 104.5 ug per tab) Everclear Vodka Either a 10ml syringe or a 4x3ml syringes (I prefer 4x3ml for a later step) A pyrex dish or porcelain plate that is roughly the same size as your page A drying surface such as a bed of nails or something else with limited contact and uniform support. I had a custom glass bed of nails made in a pyrex dish, had a blower friend make it for a sheet.
Optional: A magnetic stirrer An analytical balance scale if you have more than 100mg of crystal. Only an analytical balance good to .1mg will do. That means it can determine a difference of 100ug.
First off I can hear you saying, "WOAH Everclear and Vodka, why? Don't people just use Everclear?"
To answer this I give you an partial entry from Tihkal. The last lines from Synthesis read,
"Repeated recrystallizations from methanol produced a product that became progressively less soluble, and eventually virtually insoluble, as the purity increased. A totally pure salt, when dry and when shaken in the dark, will emit small flashes of white light. "
The final part is just to make you smile. But you will note as purity increases alcohol solubility decreases, this is why we bring out the vodka so that we can assist the solubility by adding water that we know is clean and mixed well with alcohol. Most salts, HCL, Fumurate, Mallerate and others all are water soluble.
Take your Everclear and your vodka and mix them in the ratio of 8:2 (Everclear:Vodka). Eight parts Everclear to two parts Vodka. I mix solvents to make about 100ml at a time, then store once mixed in an airtight container.
Mix it well, preferably using a magnetic stirrer for an hour if not use a large 3-10ml syringe and suck and spray it for about 15 minutes to ensure somewhat uniform mixing.
Now draw back 10 ml into the 10ml syringe, or 2.5ml per 3ml syringe, then draw some air for shaking as your solution may want to cloud up again (depends on initial mixing) if left too long as it will be what chemists call a super saturated solution. ( An important note here. Key-z needs about 10 ml of liquid Shakedown only need about 9ml; it is important that you KNOW your paper).
Lay your sheet, face down, on your chosen laying dish or plate.
Take your crystal and put it into a glass container appropriate for mixing and drawing liquid from.
Add your solvent.
Either using a magnetic stirrer or the suck and blow method, mix the living hell out of that crystal. The longer you work it the more the stubborn bits will break down and join the solution. Unless you are working with sparking crystal there will be some that just won't go. You now have the aforementioned super saturated solution.
Once you are done mixing, suck it back into your syringe(s) and cap it (them). Allow it to settle for about 2 mins to check for cloudiness and then shake it. You will note that your solution may be milky and or cloudy, that is because it is several times thicker than you would take in liquid. Super saturated. Depending on the crystal purity it will cloud more or less than another batch. If you get your alcohol and water ratio perfect it will not cloud at all.
Note- I prefer 3ml syringes for the next part but will give instructions as if you are going to understand the direction I am going.
If you have it in 4 syringes this part is easier, if it is in 1 syringe you have to be careful and pay attention to your fourths.
Turning to your sheet, you will need to think of it in fourths as well. Top quarter, middle quarters, bottom quarter.
Starting at one end begin to squirt the liquid back and forth across the pages working your way down one quarter per syringe or one quarter of your syringe, as you do each quarter, tip the sheet (very slightly) in the direction of the unfinished areas. Try to work as meticulously as possible leaving as little blank space as you can.
Tipping will help extra liquid migrate. And as you do so, you will begin to see it migrate from blotter to blotter.
Continue working down towards the end opposite from which you started. By the time you have reached the bottom you will have used 9-9.5 ml of liquid and will probably have had to tip it back to avoid run off, be careful here and you will be fine and will lose almost nothing. The remaining .3-.5ml you use to cover the last spots to have absorbed or spots that look undersaturated and then you also tip it a little bit to let is uniformly absorb the rest.
Make sure to tilt your pan or dish to ensure as it is evapping the liquid moves into the blotter uniformly, you can see this in the moisture content of the paper on the surface. Water also helps with this as it slows evap, pure Everclear can create a problem with too fast of an evap and crystal dropping out and showing on the surface of the blotter.
Once the alcohol has evapped move your sheet to your drying surface. Do not move it prematurely, wait until the liquid will not pool or cause bowing as liquid will still migrate if left and doing so would create hot spots.
Your drying surface should be something like a lipped baking dish smaller than your page, or if possible a bed of nails or glass nails.
Your sheet will dry relatively swiftly at this point and should be ready for an airtight packaging within a half hour to an hour.
Next trip testing, and blacklight checks are in order to ensure you have no hot spots.
If those come out, you are golden. Congrats you just laid a full page and contrary to the old ChinaCat post, unless you intentionally lick up the mop up, or lick solution on your hands, you will not get high at all. I have laid 5 grams at a time without getting high. The only time I accidentally dose is if I touch my mouth with solution.